1
Meet Your Remote
XR2
Xfinity Remote
All Power
TV Power
TV Input
Changes to the next
available input on your TV
(if programmed in Step 4)
Search
Discover content by
channel, program or
key words.
XFINITY / Menu
Start
Access Guide, Saved,
XFINITY On Demand, Apps,
Search and Settings.
Number Keys
Setup
Swap
Program remote for Aim
Switches between two DVR
Anywhere or to control your
tuners so you can control
TV or audio device.
playback of two channels.
2
Turn On Your Remote
3
Program Your Remote To Control Your
Set-Top Box
Install batteries in the remote and turn on your devices.
Your remote is preprogrammed to operate XFINITY cable boxes. If you are
using the remote for control of a non-XFINITY cable box, you may need to
program the remote for the Motorola or Cisco mode. Follow the steps below to
program your remote.
A
To set up your remote, first install AA batteries
(sold separately). The All Power key will blink
green four times as the remote powers up
(about 5 seconds).
Back
B
Turn on your TV.
C
Turn on your cable box.
4
Pair Remote for "Aim Anywhere" Control
Control your cable box without having to point at it, even when it is inside a
cabinet or entertainment center.
Aim Anywhere is only supported on certain XFINITY cable boxes. To see if your
cable box supports Aim Anywhere control visit xfinity.com/remotes
A
Press the Setup button until the All Power key
A
Press the Setup button until the All Power key
on the remote changes from red to green.
on the remote changes from red to green.
B
Press B for control of a Motorola brand
B
Press the XFINITY button.
cable box; press C for control of a Cisco
or Scientific-Atlanta brand cable box.
Note: If you need to re-program the remote
for control of an XFINITY cable box, repeat
the steps above and press A in step 2.
C
Press the XFINITY key to check that your
C
Follow the on-screen instruction to enter the
remote controls your set-top box. If it does,
3-digit code that appears.
you're all set. If not, repeat these steps but
press C for Cisco mode or A for XFINITY
Once the code is correctly entered, your
mode in step B.
XFINITY Remote is paired with the device.
Once the code is correctly entered, your
XFINITY Remote is paired with the device.
Not working? Make sure to install batteries in the
?
remote, check that your TV is on and that you are
entering the correct 3-digit code on your TV screen.
Need to remove Aim Anywhere control? Press
and hold the Setup button on the remote until the
?
status LED changes from red to green. Press A on
the remote. If the status LED blinks green twice,
you have successfully removed Aim Anywhere.
5
Control Your TV's Power and Volume
Popular TV Manufacturer Codes
Emerson
11864, 10171
A
Using the list on the right, find the first
Insignia
12049, 11641
5-digit code for your TV manufacturer.
JVC
11774, 12321
B
Press and hold the Setup button (about 3
LG
12731, 10178
seconds) until the Status LED changes from
red to green.
Magnavox
10054,12597
Panasonic
11480, 10051
Philips
11867, 12597
RCA
10047, 11447
Samsung
12051, 10702
C
Enter in the first 5-digit code for you TV
Sanyo
10154, 11142
manufacturer. The Status LED should blink
Sharp
10093, 12360
green twice.
Sony
10810, 11685
Toshiba
10156, 11524
VIZIO
11758, 12707
Westinghouse
11712, 13579
If your code isn't listed or you would
like to control an audio device, visit
D
Verify that the code was accepted by using
your remote to adjust volume and turn the
xfinity.com/remotes
TV on and off.
Not working? Try the second code listed. Still
not working? Visit xfinity.com/remotes for a
complete list of codes or use the My Account
app for mobile (iOS/Android) or X1.
FCC Compliance Statement
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not used in accordance with
the instructions, may cause harmful interference to
radio communications.
There is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, the user is encouraged to try to correct
the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
Increase or decrease the separation between
•
the equipment and receiver.
•
Connect the equipment into an outlet on a
circuit different from that which the receiver is
connected.
•
Consult the dealer or an experienced remote
control/ TV technician for help.
•
It is strongly recommended that the TV be
plugged into a separate wall outlet.
The user is cautioned that changes and modifications
made to this equipment without the approval of
the manufacturer could void the user's authority to
operate this equipment. This device complies with
part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may
not cause harmful interference, and (2) this device
must accept any interference received, including
interference that may cause undesired operation.
